Differences

This shows you the differences between two versions of the page.

--- en:c1_hardware_spidev [2016/04/01 13:07]
charles.park [SPIDEV Test]
+++ en:c1_hardware_spidev [2016/06/17 14:26] (current)
odroid [SPI-mode change test]
@@ Line 4: / Line 4: @@
 **SPI (/dev/spidev0.0)**
-^Pin Number^Net Name^Export Number^
+^  Pin Number  ^  Net Name  ^  Export Number  ^
-^:::^:::^C0/C1/C1+^
+^  :::  ^  :::  ^  C0/C1/C1+  ^
 |  19  |  SPI-MOSI(GPIOX.10)  |  107  |
 |  21  |  SPI-MISO(GPIOX.9)   |  106  |
@@ Line 12: / Line 12: @@
 ===== Loading SPI driver =====
-Dedicated pins for SPI are configured for GPIO, these pins can be configured as I2C bus while change the pin configuration. In order to change the configuration, you must load the driver.
+Dedicated pins for SPI are configured for GPIO, these pins can be configured as SPI bus while change the pin configuration. In order to change the configuration, you must load the driver.
 <code>
-$ modprobe spicc
+$ sudo modprobe spicc
 </code>
@@ Line 28: / Line 28: @@
 spidev 16 bits per word, clock speed = 1Mhz
 <code>
-$ sudo ./spidev_test -D /dev/spidev0.0 -s 1000000 -b 8
+$ sudo ./spidev_test -D /dev/spidev0.0 -s 1000000 -b 16
 </code>
@@ Line 35: / Line 35: @@
 spidev 32 bits per word, clock speed = 1Mhz
 <code>
-$ sudo ./spidev_test -D /dev/spidev0.0 -s 1000000 -b 8
+$ sudo ./spidev_test -D /dev/spidev0.0 -s 1000000 -b 32
 </code>
 {{http://dn.odroid.com/wiki_image/a.png?500|SPIDEV-32bits-1Mhz}}
+===== SPI-mode change test =====
+<WRAP  left round important 100%>
+**Update**\\
+SPI mode works correctly only with kernel version 3.10.96-151 or higher\\
+</WRAP>\\
+\\
+spidev 32 bits per word, spi mode = 0 \\
+<code>
+$ sudo ./spidev_test -D /dev/spidev0.0 -s 1000000 -b 32
+</code>
+{{http://dn.odroid.com/wiki_image/spi_mode_0.png?500|SPIDEV-32bits-mode-0}}
+spidev 32 bits per word, spi mode = 1
+<code>
+$ sudo ./spidev_test -D /dev/spidev0.0 -s 1000000 -b 32 -H
+</code>
+{{http://dn.odroid.com/wiki_image/spi_mode_1.png?500|SPIDEV-32bits-mode-1}}
+spidev 32 bits per word, spi mode = 2
+<code>
+$ sudo ./spidev_test -D /dev/spidev0.0 -s 1000000 -b 32 -O
+</code>
+{{http://dn.odroid.com/wiki_image/spi_mode_2.png?500|SPIDEV-32bits-mode-2}}
+spidev 32 bits per word, spi mode = 3
+<code>
+$ sudo ./spidev_test -D /dev/spidev0.0 -s 1000000 -b 32 -H -O
+</code>
+{{http://dn.odroid.com/wiki_image/spi_mode_3.png?500|SPIDEV-32bits-mode-3}}
+** spidev_test source code **
+spidev test code compile.
+<code>
+$ gcc -o spidev_test spidev_test.c
+</code>
+<file c spidev_test.c>
+/*
+ * SPI testing utility (using spidev driver)
+ *
+ * Copyright (c) 2007  MontaVista Software, Inc.
+ * Copyright (c) 2007  Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ *
+ * Cross-compile with cross-gcc -I/path/to/cross-kernel/include
+ */
+#include <stdint.h>
+#include <unistd.h>
+#include <stdio.h>
+#include <stdlib.h>
+#include <getopt.h>
+#include <fcntl.h>
+#include <sys/ioctl.h>
+#include <linux/types.h>
+#include <linux/spi/spidev.h>
+#define ARRAY_SIZE(a) (sizeof(a) / sizeof((a)[0]))
+static void pabort(const char *s)
+{
+	perror(s);
+	abort();
+}
+static const char *device = "/dev/spidev1.1";
+static uint8_t mode;
+static uint8_t bits = 8;
+static uint32_t speed = 500000;
+static uint16_t delay;
+static void transfer(int fd)
+{
+	int ret;
+	uint8_t tx[] = {
+x01, 0x02, 0x03, 0x04,
+	};
+	uint8_t rx[ARRAY_SIZE(tx)] = {0, };
+	struct spi_ioc_transfer tr = {
+		.tx_buf = (unsigned long)tx,
+		.rx_buf = (unsigned long)rx,
+		.len = ARRAY_SIZE(tx),
+		.delay_usecs = delay,
+		.speed_hz = speed,
+		.bits_per_word = bits,
+	};
+	ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr);
+	if (ret < 1)
+		pabort("can't send spi message");
+	for (ret = 0; ret < ARRAY_SIZE(tx); ret++) {
+		if (!(ret % 6))
+			puts("");
+		printf("%.2X ", rx[ret]);
+	}
+	puts("");
+}
+static void print_usage(const char *prog)
+{
+	printf("Usage: %s [-DsbdlHOLC3]\n", prog);
+	puts("  -D --device   device to use (default /dev/spidev1.1)\n"
+	     "  -s --speed    max speed (Hz)\n"
+	     "  -d --delay    delay (usec)\n"
+	     "  -b --bpw      bits per word \n"
+	     "  -l --loop     loopback\n"
+	     "  -H --cpha     clock phase\n"
+	     "  -O --cpol     clock polarity\n"
+	     "  -L --lsb      least significant bit first\n"
+	     "  -C --cs-high  chip select active high\n"
+	     "  -3 --3wire    SI/SO signals shared\n");
+	exit(1);
+}
+static void parse_opts(int argc, char *argv[])
+{
+	while (1) {
+		static const struct option lopts[] = {
+			{ "device",  1, 0, 'D' },
+			{ "speed",   1, 0, 's' },
+			{ "delay",   1, 0, 'd' },
+			{ "bpw",     1, 0, 'b' },
+			{ "loop",    0, 0, 'l' },
+			{ "cpha",    0, 0, 'H' },
+			{ "cpol",    0, 0, 'O' },
+			{ "lsb",     0, 0, 'L' },
+			{ "cs-high", 0, 0, 'C' },
+			{ "3wire",   0, 0, '3' },
+			{ "no-cs",   0, 0, 'N' },
+			{ "ready",   0, 0, 'R' },
+			{ NULL, 0, 0, 0 },
+		};
+		int c;
+		c = getopt_long(argc, argv, "D:s:d:b:lHOLC3NR", lopts, NULL);
+		if (c == -1)
+			break;
+		switch (c) {
+		case 'D':
+			device = optarg;
+			break;
+		case 's':
+			speed = atoi(optarg);
+			break;
+		case 'd':
+			delay = atoi(optarg);
+			break;
+		case 'b':
+			bits = atoi(optarg);
+			break;
+		case 'l':
+			mode |= SPI_LOOP;
+			break;
+		case 'H':
+			mode |= SPI_CPHA;
+			break;
+		case 'O':
+			mode |= SPI_CPOL;
+			break;
+		case 'L':
+			mode |= SPI_LSB_FIRST;
+			break;
+		case 'C':
+			mode |= SPI_CS_HIGH;
+			break;
+		case '3':
+			mode |= SPI_3WIRE;
+			break;
+		case 'N':
+			mode |= SPI_NO_CS;
+			break;
+		case 'R':
+			mode |= SPI_READY;
+			break;
+		default:
+			print_usage(argv[0]);
+			break;
+		}
+	}
+}
+int main(int argc, char *argv[])
+{
+	int ret = 0;
+	int fd;
+	parse_opts(argc, argv);
+	fd = open(device, O_RDWR);
+	if (fd < 0)
+		pabort("can't open device");
+	/*
+	 * spi mode
+	 */
+	ret = ioctl(fd, SPI_IOC_WR_MODE, &mode);
+	if (ret == -1)
+		pabort("can't set spi mode");
+	ret = ioctl(fd, SPI_IOC_RD_MODE, &mode);
+	if (ret == -1)
+		pabort("can't get spi mode");
+	/*
+	 * bits per word
+	 */
+	ret = ioctl(fd, SPI_IOC_WR_BITS_PER_WORD, &bits);
+	if (ret == -1)
+		pabort("can't set bits per word");
+	ret = ioctl(fd, SPI_IOC_RD_BITS_PER_WORD, &bits);
+	if (ret == -1)
+		pabort("can't get bits per word");
+	/*
+	 * max speed hz
+	 */
+	ret = ioctl(fd, SPI_IOC_WR_MAX_SPEED_HZ, &speed);
+	if (ret == -1)
+		pabort("can't set max speed hz");
+	ret = ioctl(fd, SPI_IOC_RD_MAX_SPEED_HZ, &speed);
+	if (ret == -1)
+		pabort("can't get max speed hz");
+	printf("spi mode: %d\n", mode);
+	printf("bits per word: %d\n", bits);
+	printf("max speed: %d Hz (%d KHz)\n", speed, speed/1000);
+	transfer(fd);
+	close(fd);
+	return ret;
+}
+</file>