Android

This page will introduce you how you can download and build Android source tree to customize it for your usage.

For Linux kernel and U-boot, you must install specific toolchains. Android will use its prebuilt ARM toolchain.

http://odroid.com/dokuwiki/doku.php?id=en:c2_building_u-boot#toolchain

http://odroid.com/dokuwiki/doku.php?id=en:c2_building_kernel#toolchain_492

This command will initiate to download Android source tree for ODROID-C2.
The full source includes u-boot, kernel and Android trees.

$ mkdir odroid-c2
$ cd odroid-c2
$ repo init -u https://github.com/hardkernel/android.git -b s905_5.1.1_master
$ repo sync
$ repo start s905_5.1.1_master --all

Full source code will be released in middle of December after fixing some critical issues and source code clean up.

$ mkdir odroid-c2
$ cd odroid-c2
$ repo init -u https://github.com/hardkernel/android.git -b s905_6.0.1_master
$ repo sync
$ repo start s905_6.0.1_master --all

Please make sure that you've already installed cross toolchain for kernel and U-boot before you start to build.

• Toolchain for U-boot
• Toolchain for Kernel

There is no specific build script for ODROID-C2, instead it supports generic build step what AOSP does as below.

$ export ARCH=arm64
$ export CROSS_COMPILE=aarch64-none-elf-
$ export PATH=/opt/toolchains/gcc-linaro-aarch64-none-elf-4.9-2014.09_linux/bin:$PATH
$ export PATH=/opt/toolchains/gcc-linaro-arm-none-eabi-4.8-2014.04_linux/bin:$PATH
$ export JAVA_HOME=/usr/lib/jvm/java-1.7.0-openjdk-amd64
$ export PATH=$JAVA_HOME/bin:$PATH

$ source build/envsetup.sh
$ lunch odroidc2-eng-32
$ make -j4 selfinstall

$ export ARCH=arm64
$ export CROSS_COMPILE=aarch64-linux-gnu-
$ export PATH=/opt/gcc-linaro-aarch64-linux-gnu-4.9-2014.09_linux/bin:$PATH
$ export PATH=/opt/toolchains/gcc-linaro-arm-none-eabi-4.8-2014.04_linux/bin:$PATH
$ export JAVA_HOME=/usr/lib/jvm/java-1.7.0-openjdk-amd64
$ export PATH=$JAVA_HOME/bin:$PATH

$ source build/envsetup.sh
$ lunch odroidc2-eng-32
$ make -j4 selfinstall

You can replace the number on the command make for simultaneous compile as much as number of core on your build machine. But it should not to exceed 16, otherwise build would stop with an error.

Once Android build is completed, you will have all necessary files to download into your MicroSD/eMMC. If you already have a boot media and can switch to fastboot mode is U-boot, you can proceed to update while executing below commands one by one or ignore particular steps.

$ fastboot flash bootloader out/target/product/odroidc2/u-boot.bin

$ sudo fastboot flash dtb out/target/product/odroidc2/obj/KERNEL_OBJ/arch/arm64/boot/dts/meson64_odroidc2.dtb
$ sudo fastboot flash boot out/target/product/odroidc2/obj/KERNEL_OBJ/arch/arm64/boot/Image

These three files contains Linux utilities, Android frameworks and pre-installed Android applicatioins as well as necessary files to run Android. These three files will be flash into its own partition dedicated, please find the partition table pre-defined for each partition's size.

$ sudo fastboot flash system out/target/product/odroidc2/rootsystem.img
$ sudo fastboot flash cache out/target/product/odroidc2/cache.img

These file are not mandatory for Android to use, but useful for further features. recovery.img helps you to update Android system, ODROID-C2 use this for installatioin. hardkernel-720.bmp is to show a logo on your HDMI display on boot and disappear when Android display subsystem is initiated.

$ sudo fastboot flash recovery out/target/product/odroidc2/recovery.img
$ sudo fastboot flash logo out/target/product/odroidc2/hardkernel-720.bmp.gz

This is the same way how Hardkernel team create Android release image and most easiest way to have bootable media on your ODROID-C2 if you proceed one more build step. This procedure combine all required image files created by Android build into single file, out/target/product/odroidc2/selfinstall-odroidc2.bin.

$ make selfinstall

You need USB-serial kit. You must press any key on your keyboard when ODROID-C2 is started. This will stop booting and give you U-boot command line, just execute the command fastboot.

Obviously you must have a boot media can boot from ODROID-C2 directly in order to enter fastboot mode in U-boot. Otherwise you are not able to download Android image to dedicated partitions (system/userdata/cache). The image files for such partitioins can not be downloaded from a desktop directly with dd, for example, since these images are compressed and fastboot extract while installing for each partitions.

The current U-boot does not support any other input device except serial console, hence you need USB-serial kit. Possible work around is to install a released Android image by Hardkernel team, and execute a command reboot fastboot from Android's shell command line. It will restart ODROID-C2 and stop on U-boot to get into fastboot mode. You can execute command fastboot from your desktop while USB cable is connected with ODROID-C2.

ODROID-C2's Android file system is little bit different with others for easy customizing. We made another Android system image file, rootsystem.img, which is combined with Linux root file system. We don't use boot.img as well as system.img but download Linux kernel image and rootsystem.img instead.