Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
ko:odroidsmartpower [2013/09/13 16:52] john1117 [How to write firmware] |
ko:odroidsmartpower [2013/09/16 10:09] john1117 [How to write firmware] |
||
---|---|---|---|
Line 59: | Line 59: | ||
====== Software ====== | ====== Software ====== | ||
---- | ---- | ||
+ | ===== How to write bootloader ===== | ||
+ | |||
===== How to write firmware ===== | ===== How to write firmware ===== | ||
- | === Cross Compiler install === | + | === Cross Compiler 설치 === |
MPLAB C18 v3.43 or higher (From Microchip homepage : | MPLAB C18 v3.43 or higher (From Microchip homepage : | ||
http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1406&dDocName=en010014&redirects=c18) | http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1406&dDocName=en010014&redirects=c18) | ||
In my case, Standard-Eval Version (Free of Charge) was downloaded for my code optimization. It is the trial version and can only be used for 60 days. | In my case, Standard-Eval Version (Free of Charge) was downloaded for my code optimization. It is the trial version and can only be used for 60 days. | ||
- | === IDE install === | + | === IDE 설치 === |
USB framework, main Smart Power firmware 소스 컴파일을 위한 통합개발환경 다운로드\\ | USB framework, main Smart Power firmware 소스 컴파일을 위한 통합개발환경 다운로드\\ | ||
X IDE v1.51 or higher (From Microchip homepage : http://www.microchip.com/pagehandler/en-us/family/mplabx ) | X IDE v1.51 or higher (From Microchip homepage : http://www.microchip.com/pagehandler/en-us/family/mplabx ) | ||
Line 79: | Line 81: | ||
* USB/Device - Bootloaders/HID 폴더의 HIDBootloader (windows)를 실행합니다. | * USB/Device - Bootloaders/HID 폴더의 HIDBootloader (windows)를 실행합니다. | ||
* Smart Power의 ON/OFF버튼을 누른채 Smart Power와 PC를 micro usb cable로 연결합니다. | * Smart Power의 ON/OFF버튼을 누른채 Smart Power와 PC를 micro usb cable로 연결합니다. | ||
- | * ON/OFF 버튼과 START/STOP버튼 사이의 LED중 위에 LED가 점멸하는것을 확인합니다. | + | * ON/OFF 버튼과 START/STOP버튼 사이의 LED중 위에 LED가 점멸 하는것을 확인합니다. |
* HIDBootloader에서 import firmware image 버튼을 눌러 hex파일을 선택합니다. | * HIDBootloader에서 import firmware image 버튼을 눌러 hex파일을 선택합니다. | ||
* Erase/Program/Verify Device 버튼을 누릅니다. | * Erase/Program/Verify Device 버튼을 누릅니다. | ||
* 마지막으로 Reset Device 버튼을 누르면 firmware 쓰기가 완료됩니다. | * 마지막으로 Reset Device 버튼을 누르면 firmware 쓰기가 완료됩니다. |