Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
en:odroid-c1 [2016/04/05 14:15] odroid [C1+ Lot history] |
en:odroid-c1 [2017/02/21 16:40] odroid [Software Platform] |
||
---|---|---|---|
Line 20: | Line 20: | ||
|LOT| PCB Revision| Description| | |LOT| PCB Revision| Description| | ||
|EL-1507| rev0.4 20150615 | ILIM resistor of NC380 is 6.49k ohm.| | |EL-1507| rev0.4 20150615 | ILIM resistor of NC380 is 6.49k ohm.| | ||
- | |EL-1511| rev0.4 20150930 | Changed to MP62551 from NCP380 due to component shortage.ILIM resistor of MP62551 is 20Kohms.| | + | |EL-1511| rev0.4 20150930 | Changed to MP62551 from NCP380 due to component shortage. ILIM resistor of MP62551 is 20Kohms.| |
- | |EL-1602| ::: | ::: | | + | |EL-1602| rev0.4 20160226 | Added a J9 header holes for easier soldering of alternative power input | |
====== C0 Lot history ====== | ====== C0 Lot history ====== | ||
Line 45: | Line 45: | ||
* [[C1_Lirc|Suppport custom remote controller]] | * [[C1_Lirc|Suppport custom remote controller]] | ||
* [[http://forum.odroid.com/viewtopic.php?f=112&t=17774&p=118897#p118897|HDMI OVERSCAN Adjustment]] | * [[http://forum.odroid.com/viewtopic.php?f=112&t=17774&p=118897#p118897|HDMI OVERSCAN Adjustment]] | ||
+ | * [[en:c2_lirc_gpio_blaster| Support GPIO based IR Blaster]] | ||
====== Software Platform ====== | ====== Software Platform ====== | ||
Line 55: | Line 56: | ||
* [[OpenGL ES 2.0 programming for ODROID-C1|Mali Linux SDK for ODROID-C1/C1+]] | * [[OpenGL ES 2.0 programming for ODROID-C1|Mali Linux SDK for ODROID-C1/C1+]] | ||
* [[C1_Watchdog_Timer|Watchdog_Timer on Linux]] | * [[C1_Watchdog_Timer|Watchdog_Timer on Linux]] | ||
+ | * [[en:c1_turn_off_monitor | How to turn off your monitor ]] | ||
+ | * [[en:c1_overclocking | How to overclock ODROID-C1/C1+ ]] | ||
+ | * [[en:minimal_image_wifi_setup|Configure Wireless using wpa_supplicant on minimal image or command line]] | ||
====== Expansion Boards and Accessories ====== | ====== Expansion Boards and Accessories ====== | ||
===== Ubuntu ===== | ===== Ubuntu ===== | ||
Line 67: | Line 71: | ||
* [[en:c1_hardware_spidev|SPI]] | * [[en:c1_hardware_spidev|SPI]] | ||
* [[en:c1_gpio_pps|GPIO PPS]] | * [[en:c1_gpio_pps|GPIO PPS]] | ||
+ | * [[en:c2_lirc_gpio_blaster|GPIO IR Blaster]] | ||
* [[C_Tinkering | Use the C-Tinkering Kit]] | * [[C_Tinkering | Use the C-Tinkering Kit]] | ||
* [[C1_LCDSHIELD | Use the C-3.2inch TFT+Touchscreen Shield]] | * [[C1_LCDSHIELD | Use the C-3.2inch TFT+Touchscreen Shield]] | ||
+ | * [[3.5inch_lcd_shield | Use the C-3.5inch TFT+Touchscreen Shield]] | ||
* [[C_LCDIO | Use the C-16x2 LCD IO shield]] | * [[C_LCDIO | Use the C-16x2 LCD IO shield]] | ||
* [[C1_WB_16x2lcd | Use the Weather-Board with IO shield]] | * [[C1_WB_16x2lcd | Use the Weather-Board with IO shield]] | ||
Line 76: | Line 82: | ||
* C1 Compatible 3rd party add-on boards [[http://forum.odroid.com/viewtopic.php?f=115&t=8181|Link to the Forum]] | * C1 Compatible 3rd party add-on boards [[http://forum.odroid.com/viewtopic.php?f=115&t=8181|Link to the Forum]] | ||
* [[en:c0_read_battery_voltage| Read battery voltage on ODROID-C0]] | * [[en:c0_read_battery_voltage| Read battery voltage on ODROID-C0]] | ||
+ | * [[en:gpiomem|Rootless GPIO access: /dev/gpiomem]] | ||
* [[C1_FAQ|FAQ]] | * [[C1_FAQ|FAQ]] | ||
===== Android ===== | ===== Android ===== | ||
Line 101: | Line 108: | ||
* [[http://forum.odroid.com/viewtopic.php?f=114&t=11962|DietPi (Debian Jessie)]] | * [[http://forum.odroid.com/viewtopic.php?f=114&t=11962|DietPi (Debian Jessie)]] | ||
* [[http://forum.odroid.com/viewtopic.php?f=114&t=17569|Minimal Debian Jessie]] | * [[http://forum.odroid.com/viewtopic.php?f=114&t=17569|Minimal Debian Jessie]] | ||
+ | * [[http://forum.odroid.com/viewtopic.php?f=114&t=25120|Buildroot]] | ||
+ | * [[http://www.volkspc.org/demo/|volkspc runs both Android and Debian Jessie applications simultaneously]] |