odroid-c2:software:c2_nfsboot [ODROID Wiki]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Boot linux over NFS ======
The following text describes on how to use NFS for the root filesystem. For the rest of this text 'client' means the diskless system, and 'server' means the NFS server.

<note important>If you have any trouble to setup the NFS boot, refer genosensor guide in this link.\\
[[https://forum.odroid.com/viewtopic.php?f=138&t=27034]]
</note>

===== NFS server settings (HOST PC) =====
Install nfs pakages.
  sudo apt-get install nfs-kernel-server nfs-common

After insert your eMMC or SD card, copy the Root File System.
  # The rootfs folder is mounted your RFS by SD card.
  sudo cp -rp /media/$USER/rootfs /home/$USER/rootfs

**Note: You can also user rsync to copy all file.**
  mkdir /tmp/rootfs
  mount /dev/sdb2 /tmp/rootfs
  rsync -avzh /tmp/rootfs /home/$USER/rootfs
  sync
  umount /dev/sdb2

Add following line in "/etc/exports"
  /home/$USER/rootfs        *(rw,sync,no_root_squash,no_subtree_check)
Restart NFS service.
  sudo service nfs-kernel-server restart
Modify /home/$USER/rootfs/etc/network/interfaces
<code>
# interfaces(5) file used by ifup(8) and ifdown(8)

auto lo
iface lo inet loopback
</code>

===== Kernel configuration on Odroid C2 =====
<WRAP center round important 100%>
To use the NFS, you first need to update the kernel version to "3.14.65-74" or higher.
  sudo apt-get update && sudo apt-get dist-upgrade
</WRAP>

To use Ethernet and NFS on initramfs you need to change module to built-in.

==== kernel configuration ====
Location:
<code>
-> File systems
  -> Network File Systems
     <*> NFS client support
     <*> NFS client support for NFS version 3
</code>

Then, Update your ODROID's kernel.\\
Refer to the following links How to kernel update.\\
  * [[en:c2_building_kernel | ODROID-C2 kernel update]]

===== NFS Client(Target Board) settings =====
==== How to add the boot argument ====
You shuled modify boot.ini file or compile to a u-boot script.

Append following line to the boot argument.
  boot=nfs root=/dev/nfs ip=dhcp nfsroot=${rfspath} rw

Modify "/media/boot/boot.ini"
<code>
setenv rfspath 192.168.0.22:/home/john/rootfs
setenv bootargs "boot=nfs root=/dev/nfs ip=dhcp nfsroot=${rfspath} rw rootwait ro ${condev} no_console_suspend vdaccfg=0xa000 logo=osd1,loaded,0x7900000,720p,full dmfc=3 cvbsmode=576cvbs hdmimode=${m} m_bpp=${m_bpp} vout=${vout_mode} ${disableuhs}"
</code>

In order to mount the filesystem via NFS in RW mode we need to update the /etc/fstab of the.

**Note: update the NFS/etc/fstab.**

<code>
192.168.30.27:/home/john/nfs/c2/rootfs / nfs defaults 0 0
</code>

Reboot.
  sudo reboot

Nice to have a lot of disk space:
<code>
odroid@odroid64:~$ df -h
Filesystem                              Size  Used Avail Use% Mounted on
udev                                    734M     0  734M   0% /dev
tmpfs                                   172M  5.0M  167M   3% /run
192.168.30.27:/home/john/nfs/c2/rootfs  392G   57G  315G  16% /
tmpfs                                   860M  100K  860M   1% /dev/shm
tmpfs                                   5.0M  4.0K  5.0M   1% /run/lock
tmpfs                                   860M     0  860M   0% /sys/fs/cgroup
/dev/mmcblk0p1                          128M   20M  108M  16% /media/boot
cgmfs                                   100K     0  100K   0% /run/cgmanager/fs
tmpfs                                   172M   20K  172M   1% /run/user/118
tmpfs                                   172M     0  172M   0% /run/user/1000
</code>

Dmesg output:
<code>
odroid@odroid64:~$ dmesg
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.14.29+ (john@pc) (gcc version 4.8.4 (Ubuntu/Linaro 4.8.4-2ubuntu1~14.04.1) ) #1 SMP PREEMPT Mon May 30 13:04:40 KST 2016
[    0.000000] CPU: AArch64 Processor [410fd034] revision 4
[    0.000000] secmon: share mem setup
[    0.000000] Reserved memory: initialized node linux,secmon, compatible id aml_secmon_memory
[    0.000000] __reserved_mem_alloc_size: linux,meson-fb
[    0.000000] fb: Reserved memory: created fb at 0x0000000078000000, size 128 MiB
[    0.000000] Reserved memory: initialized node linux,meson-fb, compatible id amlogic, fb-memory
[    0.000000] __reserved_mem_alloc_size: linux,di
[    0.000000] DI reserved memory: created CMA memory pool at 0x0000000076200000, size 30 MiB
[    0.000000] Reserved memory: initialized node linux,di, compatible id amlogic, di-mem
[    0.000000] __reserved_mem_alloc_size: linux,ion-dev
[    0.000000] linux,ion-dev add multi user:ffffffc001c3ac48
[    0.000000] ion_dev mem setup
[    0.000000] Reserved memory: initialized node linux,ion-dev, compatible id amlogic, idev-mem
[    0.000000] ppmgr share mem setup
[    0.000000] linux,ion-dev add multi user:ffffffc001c43508
[    0.000000] Reserved memory: initialized node linux,ion-dev, compatible id amlogic, idev-mem
[    0.000000] __reserved_mem_alloc_size: linux,codec_mm_cma
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000067800000, size 188 MiB
[    0.000000] Reserved memory: initialized node linux,codec_mm_cma, compatible id shared-dma-pool
[    0.000000] __reserved_mem_alloc_size: linux,picdec
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000064800000, size 48 MiB
[    0.000000] Reserved memory: initialized node linux,picdec, compatible id shared-dma-pool
[    0.000000] __reserved_mem_alloc_size: linux,codec_mm_reserved
[    0.000000] codec_mm:vdec: reserved mem setup
[    0.000000] Reserved memory: initialized node linux,codec_mm_reserved, compatible id amlogic, codec-mm-reserved
[    0.000000] cma: Reserved 8 MiB at 5fc00000
[    0.000000] On node 0 totalpages: 486912
[    0.000000]   Normal zone: 8568 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 486912 pages, LIFO batch:31
[    0.000000] psci: probing function IDs from device-tree
[    0.000000] PERCPU: Embedded 12 pages/cpu @ffffffc0741a9000 s19456 r8192 d21504 u49152
[    0.000000] pcpu-alloc: s19456 r8192 d21504 u49152 alloc=12*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 478344
[    0.000000] Kernel command line: boot=nfs root=/dev/nfs ip=dhcp nfsroot=192.168.30.27:/home/john/nfs/c2/rootfs rw rootwait rw console=ttyS0,115200n8 console=tty0 no_console_suspend hdmimode=1080p60hz m_bpp=32 vout= fsck.fix=yes net.ifnames=0
[    0.000000] logo: get hdmimode: 1080p60hz
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Memory: 1501820K/1947648K available (7746K kernel code, 884K rwdata, 2704K rodata, 891K init, 3162K bss, 445828K reserved)
[    0.000000] Virtual kernel memory layout:
                   vmalloc : 0xffffff8000000000 - 0xffffff8040000000   (  1024 MB)
                   vmemmap : 0xffffff8040010000 - 0xffffff80421d0000   (    33 MB)
                   modules : 0xffffffbffc000000 - 0xffffffc000000000   (    64 MB)
                   memory  : 0xffffffc000000000 - 0xffffffc078000000   (  1920 MB)
                     .init : 0xffffffc001ab6000 - 0xffffffc001b94c00   (   891 kB)
                     .text : 0xffffffc001080000 - 0xffffffc001ab5ac4   ( 10455 kB)
                     .data : 0xffffffc001b95000 - 0xffffffc001c72050   (   885 kB)
[    0.000000] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000006] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483648000ns
[    0.000023] mclk->mux_reg =ffffff8000002990,mclk->reg =ffffff800000a994
[    0.000069] local timer MESON TIMER-G mclk->mux_reg =ffffff8000002990,mclk->reg =ffffff800000c998
[    0.000090] local timer MESON TIMER-H mclk->mux_reg =ffffff8000002990,mclk->reg =ffffff800000e99c
[    0.000110] local timer MESON TIMER-I mclk->mux_reg =ffffff8000002990,mclk->reg =ffffff80000109a0
[    0.000122] Switching to timer-based delay loop
[    0.000335] Console: colour dummy device 80x25
[    0.000833] console [tty0] enabled
[    0.003185] allocated 8388608 bytes of page_cgroup
[    0.003195] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.003215] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
[    0.003233] pid_max: default: 32768 minimum: 301
[    0.003329] Security Framework initialized
[    0.003357] AppArmor: AppArmor initialized
[    0.003400] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.003413] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.005274] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[    0.005290] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[    0.005304] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[    0.005318] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[    0.007005] Initializing cgroup subsys debug
[    0.007018] Initializing cgroup subsys memory
[    0.007037] Initializing cgroup subsys devices
[    0.007047] Initializing cgroup subsys freezer
[    0.007058] Initializing cgroup subsys net_cls
[    0.007067] Initializing cgroup subsys blkio
[    0.007076] Initializing cgroup subsys perf_event
[    0.007090] Initializing cgroup subsys net_prio
[    0.007100] Initializing cgroup subsys hugetlb
[    0.007131] ftrace: allocating 28242 entries in 111 pages
[    0.032467] /cpus/cpu@0: Missing clock-frequency property
[    0.032497] /cpus/cpu@1: Missing clock-frequency property
[    0.032509] /cpus/cpu@2: Missing clock-frequency property
[    0.032521] /cpus/cpu@3: Missing clock-frequency property
[    0.032535] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[    0.071841] Meson chip version = RevB (1F:B - 0:0)
[    0.090801] CPU1: Booted secondary processor
[    0.110788] CPU2: Booted secondary processor
[    0.130779] CPU3: Booted secondary processor
[    0.130833] Brought up 4 CPUs
[    0.130863] SMP: Total of 4 processors activated.
[    0.131395] devtmpfs: initialized
[    0.143148] pinctrl core: initialized pinctrl subsystem
[    0.143424] regulator-dummy: no parameters
[    0.143741] NET: Registered protocol family 16
[    0.144404] register canvas platform driver
[    0.144415] codec:ignore bus ops for cpu=25
[    0.144423] codec:ignore bus ops for cpu=29
[    0.144431] codec:register amports ops for bus[0]
[    0.144439] codec:register amports ops for bus[4]
[    0.144447] codec:register amports ops for bus[3]
[    0.144454] codec:register amports ops for bus[2]
[    0.144461] codec:register amports ops for bus[1]
[    0.144469] codec:register amports ops for bus[13]
[    0.144477] codec:register amports ops for bus[2]
[    0.144484] codec:register amports ops for bus[14]
[    0.144506] register rdma platform driver
[    0.144859] vdso: 2 pages (1 code, 1 data) at base ffffffc001b9e000
[    0.144891] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.145411] DMA: preallocated 256 KiB pool for atomic allocations
[    0.146610] software IO TLB [mem 0x5c400000-0x5c800000] (4MB) mapped at [ffffffc05c400000-ffffffc05c7fffff]
[    0.146624] Serial: AMBA PL011 UART driver
[    0.146703] hdmitx: system: amhdmitx_init
[    0.146711] hdmitx: system: Ver: 2014May6
[    0.146740] tv_vout: tv_init_module
[    0.146754] tv_vout: major number 254 for disp
[    0.146762] vout_notify: vout_register_server
[    0.146770] tv_vout: register tv module server ok
[    0.146796] codec_mm:codec_mm_module_init
[    0.146911] gxbb clk HIU base is 0xffffff800005a000
[    0.146920] gxbb clk ao base is 0xffffff800005c000
[    0.146958] register mpll_clk_out0 success done
[    0.146971] register mpll_clk_out1 success done
[    0.146981] register mpll_clk_out2 success done
[    0.147150] register sys pll success done
[    0.147194] clkrate [ xtal 	] : 24000000Hz
[    0.147203] clkrate [ 32Khz 	] : 32000Hz
[    0.147212] clkrate [ clk81 	] : 166666666Hz
[    0.147220] clkrate [ fixed_pll 	] : 2000000000Hz
[    0.147228] clkrate [ fclk_div2 	] : 1000000000Hz
[    0.147236] clkrate [ fclk_div3 	] : 666666000Hz
[    0.147244] clkrate [ fclk_div4 	] : 500000000Hz
[    0.147252] clkrate [ fclk_div5 	] : 400000000Hz
[    0.147260] clkrate [ fclk_div7 	] : 285714000Hz
[    0.147287] gxbb clock initialization complete
[    0.147388] msr_clk_reg0=ffffff800005e75c,msr_clk_reg2=ffffff800006a764
[    0.148198] amlogic iomap probe done
[    0.148341] Init pinux probe!
[    0.149051] pinmux-gxbb c1109880.pinmux: Probed amlogic pinctrl driver
[    0.149298] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[    0.149319] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[    0.149382] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[    0.149401] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[    0.149993] codec:codec map io source 0x00000000c1100000,size=1048576 to 0xffffff8000680000
[    0.150013] codec:codec map io source 0x00000000c8820000,size=65536 to 0xffffff80000a0000
[    0.150031] codec:codec map io source 0x00000000c883c000,size=8192 to 0xffffff8000094000
[    0.150110] codec:codec map io source 0x00000000c8100000,size=1048576 to 0xffffff8000800000
[    0.150131] codec:codec map io source 0x00000000d0100000,size=262144 to 0xffffff8000980000
[    0.150150] codec:codec map io source 0x00000000c8838000,size=1024 to 0xffffff8000092000
[    0.150211] codec_mm has 2 memory regions
[    0.150226] codec_mm codec_mm.14: assigned reserved memory node linux,codec_mm_cma ok
[    0.150241] codec_mm:codec_mm_reserved_init 0000000060700000->0000000064800000
[    0.150254] codec_mm codec_mm.14: assigned reserved memory node linux,codec_mm_reserved ok
[    0.150266] codec_mm:codec_mm_probe mem init done
[    0.150276] codec_mm:add reserve memory 0000000060700000(aligned 0000000060700000) size=4100000(aligned 4100000)
[    0.150302] codec_mm has 2 memory regions
[    0.150313] codec_mm codec_mm.14: assigned reserved memory node linux,codec_mm_cma ok
[    0.150326] codec_mm:codec_mm_reserved_init 0000000060700000->0000000064800000
[    0.150338] codec_mm codec_mm.14: assigned reserved memory node linux,codec_mm_reserved ok
[    0.150350] codec_mm:codec_mm reserved memory probed done
[    0.150357] codec_mm:codec_mm_probe ok
[    0.150924] VPU driver version: v01
[    0.150933] vpu driver detect cpu type: gxbaby
[    0.150949] load vpu_clk in dts: 666667000Hz(7)
[    0.150972] vpu_probe OK
[    0.151158] hdmitx: system: amhdmitx_probe
[    0.151359] hdmitx hpd irq = 89
[    0.151550] hdmitx20: Mapped PHY: 0xc0800000
[    0.151560] hdmitx20: Mapped PHY: 0xc1104400
[    0.151582] hdmitx20: Mapped PHY: 0xc8100000
[    0.151591] hdmitx20: Mapped PHY: 0xc8834000
[    0.151600] hdmitx20: Mapped PHY: 0xc883a000
[    0.151609] hdmitx20: Mapped PHY: 0xc883c000
[    0.151622] hdmitx20: Mapped PHY: 0xd0100000
[    0.151631] hdmitx20: Mapped PHY: 0xda83a000
[    0.151870] avmute set to 1
[    0.152136] canvas_probe reg=00000000c8838000,size=400
[    0.152152] canvas maped reg_base =ffffff800009e000
[    0.155406] rdma_probe
[    0.185787] bio: create slab <bio-0> at 0
[    0.186259] SCSI subsystem initialized
[    0.186410] usbcore: registered new interface driver usbfs
[    0.186447] usbcore: registered new interface driver hub
[    0.186498] usbcore: registered new device driver usb
[    0.186563] media: Linux media interface: v0.10
[    0.186593] Linux video capture interface: v2.00
[    0.186639] pps_core: LinuxPPS API ver. 1 registered
[    0.186648] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.186668] PTP clock support registered
[    0.186818] logo: logo_init
[    0.186854] Advanced Linux Sound Architecture Driver Initialized.
[    0.187152] Bluetooth: Core ver 2.18
[    0.187175] NET: Registered protocol family 31
[    0.187184] Bluetooth: HCI device and connection manager initialized
[    0.187198] Bluetooth: HCI socket layer initialized
[    0.187210] Bluetooth: L2CAP socket layer initialized
[    0.187231] Bluetooth: SCO socket layer initialized
[    0.187244] NetLabel: Initializing
[    0.187251] NetLabel:  domain hash size = 128
[    0.187258] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.187297] NetLabel:  unlabeled traffic allowed by default
[    0.187814] Switched to clocksource Timer-E
[    0.209711] AppArmor: AppArmor Filesystem Enabled
[    0.214012] NET: Registered protocol family 2
[    0.214509] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.214628] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    0.214839] TCP: Hash tables configured (established 16384 bind 16384)
[    0.214910] TCP: reno registered
[    0.214922] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    0.214964] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    0.215138] NET: Registered protocol family 1
[    0.215339] RPC: Registered named UNIX socket transport module.
[    0.215350] RPC: Registered udp transport module.
[    0.215358] RPC: Registered tcp transport module.
[    0.215365] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.215527] Unpacking initramfs...
[    0.477667] Freeing initrd memory: 8108K (ffffffc073749000 - ffffffc073f34000)
[    0.478466] kvm [1]: Using HYP init bounce page @5b02a000
[    0.478650] kvm [1]: error: no compatible GIC node found
[    0.478681] kvm [1]: error initializing Hyp mode: -19
[    0.479085] futex hash table entries: 1024 (order: 5, 131072 bytes)
[    0.479167] audit: initializing netlink subsys (disabled)
[    0.479210] audit: type=2000 audit(0.460:1): initialized
[    0.479639] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.483321] VFS: Disk quotas dquot_6.5.2
[    0.483474] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.485117] msgmni has been set to 3437
[    0.485936] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.486006] io scheduler noop registered (default)
[    0.486016] io scheduler deadline registered
[    0.486105] io scheduler cfq registered
[    0.507429] meson-rng c8834000.rng: hwrng registered
[    0.507560] mali-utgard d00c0000.mali: max pp is 3
[    0.507572] mali-utgard d00c0000.mali: set min pp to default 1
[    0.507583] mali-utgard d00c0000.mali: min pp is 1
[    0.507593] mali-utgard d00c0000.mali: set min clk default to 0
[    0.507603] mali-utgard d00c0000.mali: min clk  is 0
[    0.507618] mali-utgard d00c0000.mali: hiu io source  0xffffff80000d2000
[    0.507634] mali-utgard d00c0000.mali: hiu io source  0xffffff80000e4000
[    0.507645] mali-utgard d00c0000.mali: num of pp used most of time 3
[    0.507656] mali-utgard d00c0000.mali: clock dvfs table size is 6
[    0.507667] mali-utgard d00c0000.mali: max clk set 4
[    0.507676] mali-utgard d00c0000.mali: max clk  is 4
[    0.507686] mali-utgard d00c0000.mali: turbo clk set to 5
[    0.507695] mali-utgard d00c0000.mali: turbo clk  is 5
[    0.507705] mali-utgard d00c0000.mali: default clk set to 2
[    0.507715] mali-utgard d00c0000.mali: default clk  is 2
[    0.507772] mali-utgard d00c0000.mali: ====================0====================
               clk_freq= 125000000, clk_parent=fclk_div4, voltage=1150, keep_count=5, threshod=<30 120>, clk_sample=125
[    0.507798] mali-utgard d00c0000.mali: ====================1====================
               clk_freq= 285000000, clk_parent=fclk_div7, voltage=1150, keep_count=5, threshod=<100 190>, clk_sample=285
[    0.507844] mali-utgard d00c0000.mali: ====================2====================
               clk_freq= 400000000, clk_parent=fclk_div5, voltage=1150, keep_count=5, threshod=<152 207>, clk_sample=400
[    0.507870] mali-utgard d00c0000.mali: ====================3====================
               clk_freq= 500000000, clk_parent=fclk_div4, voltage=1150, keep_count=5, threshod=<180 220>, clk_sample=500
[    0.507895] mali-utgard d00c0000.mali: ====================4====================
               clk_freq= 666000000, clk_parent=fclk_div3, voltage=1150, keep_count=5, threshod=<210 236>, clk_sample=666
[    0.507920] mali-utgard d00c0000.mali: ====================5====================
               clk_freq= 792000000, clk_parent=  gp0_pll, voltage=1150, keep_count=5, threshod=<230 255>, clk_sample=792
[    0.509396] gpu cooling register okay with err=0
[    0.509441] gpu core cooling register okay with err=0
[    0.509583] Mali: Mali device driver loaded
[    0.511688] loop: module loaded
[    0.512013] mtdoops: mtd device (mtddev=name/number) must be supplied
[    0.520751] libphy: stmmac: probed
[    0.520775] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[    0.520786] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
[    0.521058] usbcore: registered new interface driver cdc_ether
[    0.521115] usbcore: registered new interface driver cdc_ncm
[    0.521209] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.521220] ehci-h20ahb: H20AHB-EHCI Host Controller driver
[    0.521300] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.521359] usbcore: registered new interface driver cdc_acm
[    0.521368] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    0.521412] usbcore: registered new interface driver usb-storage
[    0.521497] usbcore: registered new interface driver usbserial
[    0.521709] mousedev: PS/2 mouse device common for all mice
[    0.521928] i2c /dev entries driver
[    0.522000] IR NEC protocol handler initialized
[    0.522009] IR RC5(x) protocol handler initialized
[    0.522017] IR RC6 protocol handler initialized
[    0.522024] IR JVC protocol handler initialized
[    0.522032] IR Sony protocol handler initialized
[    0.522040] IR RC5 (streamzap) protocol handler initialized
[    0.522048] IR SANYO protocol handler initialized
[    0.522056] IR MCE Keyboard/mouse protocol handler initialized
[    0.522493] ledtrig-cpu: registered to indicate activity on CPUs
[    0.522645] usbcore: registered new interface driver usbhid
[    0.522654] usbhid: USB HID core driver
[    0.522842] ashmem: initialized
[    0.522942] logger: created 256K log 'log_main'
[    0.523036] logger: created 256K log 'log_events'
[    0.523123] logger: created 256K log 'log_radio'
[    0.523210] logger: created 256K log 'log_system'
[    0.523453] ==uart0 reg addr = ffffff80002724c0
[    0.523480] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
[    0.523501] ttyS0 use xtal 24000000 change 0 to 115200
[    2.191428] console [ttyS0] enabled
[    2.195030] ==uart1 reg addr = ffffff80002744c0
[    2.199375] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[    2.208685] enter  cpufreq
[    2.211178] probe  cpufreq okay
[    2.216552] dwc_otg c9100000.dwc2_b: dwc_otg_driver_probe(ffffffc05d728200)
[    2.256596] dwc_otg: usb1: type: 1 speed: 0, config: 0, dma: 0, id: 1, phy: c0000020, ctrl: 0
[    2.259467] dwc_otg c9100000.dwc2_b: base=0xffffff8001680000
[    2.259474] dwc_otg c9100000.dwc2_b: dwc_otg_device=0xffffffc05a99ef00
[    2.262135] dwc_otg: Core Release: 3.10a
[    2.263337] dwc_otg: Setting default values for core params
[    2.268872] dwc_otg: curmode: 1, host_only: 1
[    2.273176] dwc_otg c9100000.dwc2_b: DMA config: BURST_DEFAULT
[    2.275360] dwc_otg: Using Buffer DMA mode
[    2.277220] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[    2.282316] dwc_otg: Working on port type = HOST
[    2.287102] dwc_otg dwc2_b: DWC OTG Controller
[    2.291296] dwc_otg dwc2_b: new USB bus registered, assigned bus number 1
[    2.298028] dwc_otg dwc2_b: irq 63, io mem 0x00000000
[    2.303008] dwc_otg: -------hcd->flags.d32 = 0
[    2.307424] dwc_otg: Init: Port Power? op_state=1
[    2.312071] dwc_otg: Init1: Power Port (0)
[    2.316558] hub 1-0:1.0: USB hub found
[    2.319861] hub 1-0:1.0: 1 port detected
[    2.323841] dwc_otg c9000000.dwc2_a: dwc_otg_driver_probe(ffffffc05d728600)
[    2.323876] dwc_otg: usb0: type: 0 speed: 0, config: 0, dma: 0, id: 0, phy: c0000000, ctrl: 0
[    2.332170] dwc_otg c9000000.dwc2_a: base=0xffffff8001700000
[    2.332175] dwc_otg c9000000.dwc2_a: dwc_otg_device=0xffffffc073962f00
[    2.344750] dwc_otg: Core Release: 3.10a
[    2.344772] dwc_otg: Setting default values for core params
[    2.348573] dwc_otg: curmode: 1, host_only: 0
[    2.354884] dwc_otg c9000000.dwc2_a: DMA config: BURST_DEFAULT
[    2.357056] dwc_otg: Using Buffer DMA mode
[    2.357078] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[    2.362020] dwc_otg: Working on port type = OTG
[    2.366496] dwc_otg: Current port type: SLAVE
[    2.370898] dwc_otg dwc2_a: DWC OTG Controller
[    2.375217] dwc_otg dwc2_a: new USB bus registered, assigned bus number 2
[    2.381955] dwc_otg dwc2_a: irq 62, io mem 0x00000000
[    2.387285] hub 2-0:1.0: USB hub found
[    2.390675] hub 2-0:1.0: 1 port detected
[    2.394633] dwc_otg: Dedicated Tx FIFOs mode
[    2.398930] dwc_otg: using timer detectid change, ffffffc07399c000
[    2.405183] secmon has 1 memory regions
[    2.408705] secmon: share in base: 0xffffff80004e6000, share out base: 0xffffff80004e8000
[    2.416782] secmon secmon.3: assigned reserved memory node linux,secmon ok
[    2.423645] secmon: probe done
[    2.426710] storage: storage in base: 0xffffff8001780000
[    2.431882] storage: storage out base: 0xffffff8001800000
[    2.437221] storage: storage block base: 0xffffff8001880000
[    2.442747] storage: probe done!
[    2.445977] Error: Driver 'ICPlus IP175C' is already registered, aborting...
[    2.452926] libphy: ICPlus IP175C: Error -16 in registering driver
[    2.459514] aml_sd_emmc_probe: line 2954
[    2.462924] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[    2.472324] aml_sd_emmc_reg_init 677
[    2.475752] pdata->caps 60007
[    2.478631] pdata->caps2 0
[    2.481296] get property:                ocr_avail, value:0x00200080
[    2.487591] get property:                    f_min, value:0x00061a80
[    2.493932] get property:                    f_max, value:0x0510ff40
[    2.500192] get property:             max_req_size, value:0x00020000
[    2.506480] get property:                   irq_in, value:0x00000003
[    2.512786] get property:                  irq_out, value:0x00000005
[    2.519116] dwc_otg: Indeed it is in host mode hprt0 = 00021501
[    2.527835] get property:              power_level, value:0x00000001
[    2.531243] get property:                  gpio_cd, str:
[    2.536498] get property:               gpio_power, str:
[    2.541765] get property:                  pinname, str:sd
[    2.547191] get property:                 jtag_pin, str:
[    2.552458] get property:                card_type, value:0x00000005
[    2.558755] get property:                gpio_dat3, str:
[    2.564011] get property:               gpio_volsw, str:
[    2.637912] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[    2.637974] aml_sd_emmc_probe: line 2954
[    2.648912] [aml_is_card_insert][0;40;33m card OUT
               [0m
[    2.657902] [aml_is_card_insert][0;40;33m card OUT
               [0m
[    2.679125] aml_sd_emmc_reg_init 677
[    2.679241] pdata->caps 80000d47
[    2.680265] pdata->caps2 80a1
[    2.683190] get property:                ocr_avail, value:0x00200080
[    2.689514] get property:                    f_min, value:0x00061a80
[    2.695782] get property:                    f_max, value:0x05f5e100
[    2.697845] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    2.698111] dwc_otg: Indeed it is in host mode hprt0 = 00001101
[    2.714335] get property:             max_req_size, value:0x00020000
[    2.720633] get property:                  pinname, str:emmc
[    2.726229] get property:                card_type, value:0x00000001
[    2.732536] get property:                gpio_dat3, str:
[    2.737787] get property:                 hw_reset, str:
[    2.797830] aml_emmc_hw_reset 1356
[    2.797832] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[    2.798027] ion_dev has 1 memory regions
[    2.817613] fb: osd_init_module
[    2.817706] fb: viu vsync irq: 35
[    2.818422] meson-fb has 1 memory regions
[    2.823515] meson-fb meson-fb.11: assigned reserved memory node linux,meson-fb ok
[    2.829807] tv_vout: tv_set_current_vmode[672]fps_target_mode=10
[    2.835740] tv_vout: mode is 10,sync_duration_den=1,sync_duration_num=60
[    2.842392] switch_vpu_mem_pd: vencp ON
[    2.846177] tv_vout: TV mode 720p60hz selected.
[    2.850679] tv_vout: new mode =720p60hz set ok
[    2.855059] vout_serve: vinfo mode is: 720p60hz
[    2.859632] switch_vpu_mem_pd: viu_osd1 ON
[    2.863598] switch_vpu_mem_pd: viu_osd2 ON
[    2.867652] switch_vpu_mem_pd: viu_osd_scale ON
[    2.871595] emmc: BKOPS_EN bit is not set
[    2.876301] [aml_sd_voltage_switch][0;40;32m switch to 1.8V for a non-uhs device.
               [0m
[    2.876302] osd_rdma: osd_rdma_init: rmda_table p=0x5fc49000,op=0x5fc49000 , v=0xffffff80004fa000
[    2.887751] emmc: clk 100000000 SDR mode tuning start
[    2.887982] rx_tuning_result[0][0] = 10
[    2.888197] rx_tuning_result[0][1] = 10
[    2.888411] rx_tuning_result[0][2] = 10
[    2.888625] rx_tuning_result[0][3] = 10
[    2.888838] rx_tuning_result[0][4] = 10
[    2.889052] rx_tuning_result[0][5] = 10
[    2.889267] rx_tuning_result[0][6] = 10
[    2.889479] rx_tuning_result[0][7] = 10
[    2.889692] rx_tuning_result[0][8] = 10
[    2.889905] rx_tuning_result[0][9] = 10
[    2.889908] best_win_start =0, best_win_size =10
[    2.889911] sd_emmc_regs->gclock =0x100024a, sd_emmc_regs->gadjust =0x2000
[    2.889914] emmc: gclock =0x100024a, gdelay=0x76965077
[    2.889916] gadjust=0x2000
[    2.890033] emmc: try set sd/emmc to DDR mode
[    2.890037] emmc: try set sd/emmc to DDR mode
[    2.890041] emmc: clk 100000000 DDR mode tuning start
[    2.890871] rx_tuning_result[0][0] = 10
[    2.891608] rx_tuning_result[0][1] = 10
[    2.892347] rx_tuning_result[0][2] = 10
[    2.893083] rx_tuning_result[0][3] = 10
[    2.893170] best_win_start =0, best_win_size =4
[    2.893173] sd_emmc_regs->gclock =0x1000245, sd_emmc_regs->gadjust =0x12000
[    2.893175] emmc: gclock =0x1000245, gdelay=0x76965077
[    2.893176] gadjust=0x12000
[    2.893548] emmc: new HS400 MMC card at address 0001
[    2.893947] emmc: clock 100000000, 8-bit-bus-width
                
[    2.893947] mmcblk0: emmc:0001 064GE2 58.2 GiB 
[    3.020095] fb: osd_probe vinfo:ffffffc001c3beb8
[    3.020755] hub 1-1:1.0: USB hub found
[    3.021013]  mmcblk0: p1 p2
[    3.021380] hub 1-1:1.0: 4 ports detected
[    3.035095] fb: Frame buffer memory assigned at
[    3.039386] fb:     phy: 0x78000000, vir:0xffffff8003c00000, size=98304K
[    3.046194] fb: osd_set_res_bootargs : mode 60
[    3.050607] fb: osd_set_res_bootargs, no available resolution info.
[    3.056627] fb: fb def : 1280 720 1280 1440 32
[    3.061206] fb: init fbdev bpp is:32
[    3.064733] fb: ---------------clear fb0 memory
[    3.096564] fb: osd[0] canvas.idx =0x40
[    3.096566] fb: osd[0] canvas.addr=0x78000000
[    3.096567] fb: osd[0] canvas.width=5120
[    3.096569] fb: osd[0] canvas.height=1440
[    3.122355] Console: switching to colour frame buffer device 160x45
[    3.153130] fb: Frame buffer memory assigned at
[    3.153217] fb:     phy: 0x7e000000, vir:0xffffff8001a00000, size=1024K
[    3.173131] fb: osd probe OK
[    3.173288] vout_serve: vout_init_module
[    3.174370] vout_serve: meson_vout_probe
[    3.178215] vout_serve: create vout attribute OK
[    3.182802] ge2d: ge2d_init_module
[    3.186125] ge2d: ge2d_dev major:245
[    3.189789] ge2d: ge2d clock is 400 MHZ
[    3.193466] ge2d: ge2d: pdev=ffffffc05d6de400, irq=182, rstc=0xffffffc07398e080, clk=ffffffc05d6a8d00
[    3.202633] ge2d: mapped phy: 0xd0160000
[    3.206479] ge2d: ge2d start monitor
[    3.210155] codec:Amlogic A/V streaming port init
[    3.215270] codec:get gate demux control ok ffffffc073809980
[    3.220306] ge2d: ge2d workqueue monitor start
[    3.220344] codec:get gate parser_top control ok ffffffc073809d80
[    3.220349] codec:get gate vpu_intr control ok ffffffc073809e80
[    3.220354] codec:get gate vdec control ok ffffffc073809f80
[    3.220549] codec:[tsync_pcr_init]init success.
[    3.220581] codec:regist mpeg12 codec profile
[    3.220613] codec:regist mpeg4 codec profile
[    3.220614] codec:amvdec_vc1 module init
[    3.220684] codec:regist vc1 codec profile
[    3.220685] codec:amvdec_h264 module init
[    3.220735] codec:regist h264 codec profile
[    3.220736] codec:amvdec_h264mvc module init
[    3.220782] codec:regist hmvc codec profile
[    3.220783] codec:amvdec_h264_4k2k module init
[    3.220815] codec:regist h264_4k2k codec profile
[    3.220816] codec:amvdec_h265 module init
[    3.220846] codec:regist hevc codec profile
[    3.220879] codec:regist mjpeg codec profile
[    3.220880] codec:amvdec_real module init
[    3.220915] codec:regist real codec profile
[    3.220916] codec:amvdec_avs module init
[    3.220946] codec:regist avs codec profile
[    3.220985] amvenc_avc_probe -- reserved memory config fail.
[    3.220987] amvenc_avc - cma memory pool size: 32 MB
[    3.220999] encode_wq_init.
[    3.221005] encode start monitor.
[    3.221070] encode workqueue monitor start.
[    3.221184] jpegenc module init
[    3.221279] codec:picdec_driver_probe called.
[    3.221282] picdec has 1 memory regions
[    3.221300] picdec picdec.19: assigned reserved memory node linux,picdec ok
[    3.221302] codec:picdec_driver_probe done.
[    3.221303] codec:reserved memory config fail , use CMA	.
[    3.223960] codec:cma memory is 64800000 , size is  3000000
[    3.224319] codec:0 addr is 64800000################
[    3.224328] codec:1 addr is 64951800################
[    3.224473] switch_vpu_mem_pd: vpu_arb ON
[    3.224703] codec:create_ge2d_work_queue video task ok
[    3.224935] codec:register clk_set_setting cpu[31]
[    3.225127] di_module_init ok.
[    3.225132] di_module_init: major 241
[    3.225250] di_probe
[    3.225339] deinterlace has 1 memory regions
[    3.225358] di reveser memory 0x76200000, size 30MB.
[    3.225365] deinterlace deinterlace.21: assigned reserved memory node linux,di ok
[    3.225466] rdma_register, rdma_table_addr ffffff8000642000 rdma_table_addr_phy 5fc4e000 reg_buf ffffffc073a4e000
[    3.225468] rdma_register success, handle 1 table_size 8192
[    3.225470] di_probe allocate rdma channel 1.
[    3.225473] DI hw version 2.
[    3.225480] 0x000000c3:Y=c3,U=0,V=0
[    3.225481] 0x000000c4:Y=c4,U=0,V=0
[    3.225483] 0x000000c5:Y=c5,U=0,V=0
[    3.225485] 0x000000c6:Y=c6,U=0,V=0
[    3.225486] 0x000000c7:Y=c7,U=0,V=0
[    3.225488] 0x000000c8:Y=c8,U=0,V=0
[    3.225489] 0x000000c9:Y=c9,U=0,V=0
[    3.225492] 0x000000ca:Y=ca,U=0,V=0
[    3.225494] 0x000000cb:Y=cb,U=0,V=0
[    3.225496] 0x000000cc:Y=cc,U=0,V=0
[    3.225498] 0x000000cd:Y=cd,U=0,V=0
[    3.225500] 0x000000ce:Y=ce,U=0,V=0
[    3.225502] 0x000000cf:Y=cf,U=0,V=0
[    3.225614] di_probe here.
[    3.225627] switch_vpu_mem_pd: di_pre OFF
[    3.225776] efusekeynum: 4
[    3.225782] efusekeyname:             mac	offset:     0	size:     6
[    3.225786] efusekeyname:          mac_bt	offset:     6	size:     6
[    3.225791] efusekeyname:        mac_wifi	offset:    12	size:     6
[    3.225795] efusekeyname:            usid	offset:    18	size:    16
[    3.225873] efuse efuse.7: probe OK!
[    3.225991] 6aml_unifykeys_init done!
[    3.225992] ppmgr module init func called
[    3.226033] ppmgr_driver_probe called
[    3.226036] ppmgr has 1 memory regions
[    3.226043] init ppmgr memsource 74200000->761fffff
[    3.226169] ppmgr_probe done
[    3.226366] ionvideo-000: V4L2 device registered as video13
[    3.226372] [dsp]register dsp to char divece(257)
[    3.226640] amaudio: driver amaudio succuess!
[    3.226644] amlvideo_init called
[    3.226644] amlvideo_create_instance called
[    3.226646] v4l2_dev.name=:amlvideo-000
[    3.226701] amlvideo-000: V4L2 device registered as video10
[    3.226703] 
               
                VECM init

[    3.226963] saradc c1108680.saradc: initialized by BL30
[    3.226967] saradc c1108680.saradc: calibration start:
[    3.227019] saradc c1108680.saradc: nominal=0, value=0
[    3.227065] saradc c1108680.saradc: nominal=256, value=250
[    3.227111] saradc c1108680.saradc: nominal=512, value=508
[    3.227159] saradc c1108680.saradc: nominal=768, value=766
[    3.227204] saradc c1108680.saradc: nominal=1023, value=1022
[    3.227207] saradc c1108680.saradc: calibration end: coef=4064
[    3.227246] remote: Driver init
[    3.227285] remote: platform_data g_remote_ao_offset=580
[    3.227287] remote: platform_data irq =228
[    3.227313] remote: set drvdata completed
[    3.227325] remote: device_create_file completed 
[    3.227612] input: aml_keypad as /devices/meson-remote.9/input/input0
[    3.227752] remote: input_register_device completed 
[    3.227872] remote: [0x480] = 0x1dd0190
[    3.227875] remote: [0x484] = 0xf800ca
[    3.227877] remote: [0x488] = 0x82006e
[    3.227880] remote: [0x48c] = 0x3c0030
[    3.227882] remote: [0x490] = 0x30fa0013
[    3.227891] remote: [0x498] = 0x6f19000
[    3.227893] remote: [0x49c] = 0xbe40
[    3.227895] remote: [0x580] = 0xfa00a0
[    3.227897] remote: [0x584] = 0xfa00a0
[    3.227900] remote: [0x588] = 0xfa00a0
[    3.227902] remote: [0x58c] = 0x640030
[    3.227905] remote: [0x590] = 0x30fa0013
[    3.227907] remote: [0x598] = 0x961b800
[    3.227909] remote: [0x59c] = 0x9740
[    3.227912] remote: [0x5a0] = 0x104
[    3.227914] remote: [0x5a4] = 0x0
[    3.227916] remote: [0x5a8] = 0x0
[    3.227919] remote: set_remote_mode[72]
[    3.227938] remote: remote config major:237
[    3.228033] remote: physical address:0x73ae4000
[    3.228395] aml-thermal : min state:1000000 400 1 2
[    3.228576] aml-thermal : not found gpucore node
[    3.228582] aml-thermal : gpu coef:437, pp:3
[    3.233618] aml-thermal : cdev1 set upper to 4
[    3.233622] aml-thermal : cdev0 set upper to 3
[    3.236171] 6--------------------------------------------------------
[    3.236173] 6odroid_sysfs_init(321) : Sleep Enable !!
[    3.236174] 6--------------------------------------------------------
[    3.236308] input: vt-input as /devices/virtual/input/input1
[    3.236376] 6Virtual-Key input driver registered!!
[    3.236809] adbattery: android dummy battery driver loaded
[    3.237156] enter aml_soc_platform_pcm2bt_probe
[    3.237370] divider=16,frac=33920000,SDMval=4523
[    3.237474] enter aml_pcm_dai_probe
[    3.237506] [aml-spdif-dai]enter aml_dai_spdif_init
[    3.237554] aml_spdif_probe
[    3.237649] enter spdif_dit_probe
[    3.238310] odroid_hdmi_snd odroid_hdmi.36: dit-hifi <-> I2S.27 mapping ok
[    3.238809] GACT probability on
[    3.238812] Mirror/redirect action on
[    3.238814] u32 classifier
[    3.238815]     Performance counters on
[    3.238816]     input device check on
[    3.238817]     Actions configured
[    3.238918] TCP: cubic registered
[    3.238927] NET: Registered protocol family 17
[    3.238959] NET: Registered protocol family 15
[    3.239078] Bluetooth: RFCOMM TTY layer initialized
[    3.239086] Bluetooth: RFCOMM socket layer initialized
[    3.239094] Bluetooth: RFCOMM ver 1.11
[    3.239100] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    3.239102] Bluetooth: BNEP filters: protocol multicast
[    3.239107] Bluetooth: BNEP socket layer initialized
[    3.239109] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.239114] Bluetooth: HIDP socket layer initialized
[    3.239133] NET: Registered protocol family 35
[    3.239221] Key type dns_resolver registered
[    3.239681] Registering SWP/SWPB emulation handler
[    3.239963] AppArmor: AppArmor sha1 policy hashing enabled
[    3.239992] regulator-dummy: disabling
[    3.240109] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    3.241554] input: cec_input as /devices/virtual/input/input2
[    3.241956] 6enter meson_pm_probe!
[    3.242043] meson_pm_probe done
[    3.242164] ALSA device list:
[    3.242166]   #0: ODROID-HDMI
[    3.298167] usb 1-1.1: new full-speed USB device number 3 using dwc_otg
[    3.405873] input: Logitech USB Receiver as /devices/dwc2_b/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C52B.0001/input/input3
[    3.406002] hid-generic 0003:046D:C52B.0001: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-dwc2_b-1.1/input0
[    3.410386] input: Logitech USB Receiver as /devices/dwc2_b/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0002/input/input4
[    3.410658] hid-generic 0003:046D:C52B.0002: input,hiddev0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-dwc2_b-1.1/input1
[    3.416109] hid-generic 0003:046D:C52B.0003: hiddev0: USB HID v1.11 Device [Logitech USB Receiver] on usb-dwc2_b-1.1/input2
[    3.759952] random: nonblocking pool is initialized
[    4.007750] Freeing unused kernel memory: 888K (ffffffc001ab6000 - ffffffc001b94000)
[    5.213130] switch_vpu_mem_pd: viu_vd1 OFF
[    5.215908] switch_vpu_mem_pd: afbc_dec OFF
[    5.218637] switch_vpu_mem_pd: di_post OFF
[    5.222544] switch_vpu_mem_pd: viu_vd2 OFF
[    8.528074] libphy: stmmac-0:00 - Link is Up - 1000/Full
[    9.167962] systemd[1]: System time before build time, advancing clock.
[    9.274517] systemd[1]: Failed to insert module 'autofs4': No such file or directory
[    9.305792] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[    9.324879] systemd[1]: Detected architecture arm64.
[    9.358100] systemd[1]: Set hostname to <odroid64>.
[    9.444715] ttyS0 use xtal 24000000 change 115200 to 115200
[   10.065585] systemd[1]: Listening on Journal Socket (/dev/log).
[   10.072699] systemd[1]: Reached target User and Group Name Lookups.
[   10.080426] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[   10.088144] systemd[1]: Reached target Swap.
[   10.094495] systemd[1]: Created slice User and Session Slice.
[   10.100911] systemd[1]: Listening on udev Control Socket.
[   10.107053] systemd[1]: Starting of Arbitrary Executable File Formats File System Automount Point not supported.
[   10.141524] systemd[1]: Listening on Process Core Dump Socket.
[   10.148554] systemd[1]: Listening on Syslog Socket.
[   10.155295] systemd[1]: Reached target Encrypted Volumes.
[   10.162421] systemd[1]: Created slice System Slice.
[   10.169242] systemd[1]: Reached target Slices.
[   10.176218] systemd[1]: Created slice system-serial\x2dgetty.slice.
[   10.183909] systemd[1]: Listening on udev Kernel Socket.
[   10.191005] systemd[1]: Listening on Journal Socket.
[   10.205137] systemd[1]: Starting Load Kernel Modules...
[   10.238261] systemd[1]: Started Read required files in advance.
[   10.248331] systemd[1]: Mounting POSIX Message Queue File System...
[   10.259093] systemd[1]: Mounting Debug File System...
[   10.269620] systemd[1]: Starting Create Static Device Nodes in /dev...
[   10.279676] systemd[1]: Starting Braille Device Support...
[   10.290835] systemd[1]: Starting Journal Service...
[   10.305469] systemd[1]: Starting Nameserver information manager...
[   10.315676] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[   10.327004] systemd[1]: Mounting Huge Pages File System...
[   10.335512] systemd[1]: Created slice system-getty.slice.
[   10.345500] systemd[1]: Starting Uncomplicated firewall...
[   10.353820] systemd[1]: Reached target Remote File Systems (Pre).
[   10.361526] systemd[1]: Reached target Remote File Systems.
[   10.371158] systemd[1]: Starting Remount Root and Kernel File Systems...
[   10.383159] systemd[1]: systemd-modules-load.service: Main process exited, code=exited, status=1/FAILURE
[   10.392720] systemd[1]: Failed to start Load Kernel Modules.
[   10.405309] systemd[1]: systemd-modules-load.service: Unit entered failed state.
[   10.410695] systemd[1]: systemd-modules-load.service: Failed with result 'exit-code'.
[   10.425451] systemd[1]: Starting Apply Kernel Variables...
[   10.438512] systemd[1]: Mounting Configuration File System...
[   10.448841] systemd[1]: Started Uncomplicated firewall.
[   10.459987] systemd[1]: Started Remount Root and Kernel File Systems.
[   10.483796] systemd[1]: Starting Load/Save Random Seed...
[   10.530977] systemd[1]: Starting udev Coldplug all Devices...
[   10.542293] systemd[1]: Mounted Configuration File System.
[   10.549300] systemd[1]: Mounted Huge Pages File System.
[   10.556391] systemd[1]: Mounted POSIX Message Queue File System.
[   10.563946] systemd[1]: Mounted Debug File System.
[   10.592147] systemd[1]: ureadahead.service: Main process exited, code=exited, status=5/NOTINSTALLED
[   10.600000] systemd[1]: ureadahead.service: Unit entered failed state.
[   10.605548] systemd[1]: ureadahead.service: Failed with result 'exit-code'.
[   10.613517] systemd[1]: Started Journal Service.
[   10.816369] systemd-journald[163]: Received request to flush runtime journal from PID 1
[   11.919484] ionvideo open
[   12.117850] ionvideo_stop_generating!!!!
[   12.117885] ionvideo release
[   14.786634] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   15.613629] cgroup: new mount options do not match the existing superblock, will be ignored
[   19.797448] fb: osd[0] canvas.idx =0x40
[   19.797451] fb: osd[0] canvas.addr=0x78000000
[   19.797453] fb: osd[0] canvas.width=5120
[   19.797455] fb: osd[0] canvas.height=720
[   19.813291] fb: osd[0] enable: 0 (Xorg)
[   20.336593] ttyS0 use xtal 24000000 change 115200 to 115200
[   20.336987] ttyS0 use xtal 24000000 change 115200 to 115200
[   20.706822] ttyS0 use xtal 24000000 change 115200 to 115200
[   20.707164] ttyS0 use xtal 24000000 change 115200 to 115200
[   20.731801] fb: osd[0] enable: 1 (Xorg)
[   27.179220] divider=17,frac=80768000,SDMval=11722
[   27.179265] i2sin_fifo0_set_buf
[   27.179357] i2sin_fifo0_set_buf
[   27.306069] i2sin_fifo0_set_buf
[   27.306184] i2sin_fifo0_set_buf
[   27.311613] [aml-i2s-dai]i2s dma ffffff800064a000,phy addr 1606811648,mode 0,ch 1
[   27.311627] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[   27.311631] aml_set_spdif_clk rate
[   27.311650] divider=22,frac=13030400,SDMval=2364
[   27.311699] set normal 512 fs /4 fs
[   27.311706] iec958 mode PCM16
[   27.311714] IEC958 16bit
[   27.311720] hdmitx: audio: aout notify rate 44100
[   27.311723] hdmitx: audio: aout notify size 16
[   27.311727] 958 with i2s
[   27.311820] [aml-i2s-dai]i2s dma ffffff800064a000,phy addr 1606811648,mode 0,ch 1
[   27.311825] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[   27.311828] aml_set_spdif_clk rate
[   27.311833] divider=22,frac=13030400,SDMval=2364
[   27.311838] set normal 512 fs /4 fs
[   27.311843] iec958 mode PCM16
[   27.311849] IEC958 16bit
[   27.311853] hdmitx: audio: aout notify rate 44100
[   27.311856] hdmitx: audio: aout notify size 16
[   27.311859] 958 with i2s
[   27.346735] i2sin_fifo0_set_buf
[   27.346819] i2sin_fifo0_set_buf
[   27.348051] i2sin_fifo0_set_buf
[   27.348131] i2sin_fifo0_set_buf
[   27.349164] [aml-i2s-dai]i2s dma ffffff800064a000,phy addr 1606811648,mode 0,ch 2
[   27.349175] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[   27.349179] aml_set_spdif_clk rate
[   27.349191] divider=22,frac=13030400,SDMval=2364
[   27.349202] set normal 512 fs /4 fs
[   27.349208] iec958 mode PCM16
[   27.349216] IEC958 16bit
[   27.349221] hdmitx: audio: aout notify rate 44100
[   27.349225] hdmitx: audio: aout notify size 16
[   27.349229] 958 with i2s
[   27.349289] [aml-i2s-dai]i2s dma ffffff800064a000,phy addr 1606811648,mode 0,ch 2
[   27.349293] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[   27.349296] aml_set_spdif_clk rate
[   27.349301] divider=22,frac=13030400,SDMval=2364
[   27.349307] set normal 512 fs /4 fs
[   27.349311] iec958 mode PCM16
[   27.349317] IEC958 16bit
[   27.349321] hdmitx: audio: aout notify rate 44100
[   27.349324] hdmitx: audio: aout notify size 16
[   27.349328] 958 with i2s
[   27.349940] i2sin_fifo0_set_buf
[   27.350000] i2sin_fifo0_set_buf
[   27.350570] i2sin_fifo0_set_buf
[   27.350627] i2sin_fifo0_set_buf
[   27.359892] [aml-i2s-dai]i2s dma ffffff800064a000,phy addr 1606811648,mode 0,ch 2
[   27.359904] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[   27.359908] aml_set_spdif_clk rate
[   27.359919] divider=22,frac=13030400,SDMval=2364
[   27.359930] set normal 512 fs /4 fs
[   27.359936] iec958 mode PCM16
[   27.359944] IEC958 16bit
[   27.359950] hdmitx: audio: aout notify rate 44100
[   27.359953] hdmitx: audio: aout notify size 16
[   27.359957] 958 with i2s
[   27.360033] [aml-i2s-dai]i2s dma ffffff800064a000,phy addr 1606811648,mode 0,ch 2
[   27.360038] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[   27.360041] aml_set_spdif_clk rate
[   27.360046] divider=22,frac=13030400,SDMval=2364
[   27.360052] set normal 512 fs /4 fs
[   27.360056] iec958 mode PCM16
[   27.360062] IEC958 16bit
[   27.360065] hdmitx: audio: aout notify rate 44100
[   27.360069] hdmitx: audio: aout notify size 16
[   27.360072] 958 with i2s
[   27.386112] aiu i2s playback enable
[   27.386135] audio_hw_958_enable 1
[   27.387510] i2sin_fifo0_set_buf
[   27.387767] i2sin_fifo0_set_buf
[   32.958858] aiu i2s playback disable
[   32.958872] audio_hw_958_enable 0
[  620.724657] fb: osd[0] enable: 1 (Xorg)
[  620.733188] fb: osd[0] enable: 0 (Xorg)
[  620.753128] fb: osd[0] enable: 0 (Xorg)
</code>