en:xu4_cloudshell2 [ODROID Wiki]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Overview ======
{{:en:acc:cs2:cs2_main.png?700|}}

The [[http://www.hardkernel.com/main/products/prdt_info.php?g_code=G149142327280|CloudShell2]] for the **ODROID-XU4** is an affordable DIY Network Attached Storage (NAS) Solution with RAID support.\\ 
It offers dual slots for 3.5” HDD/SSD drives with very fast UAS(USB Attached SCSI) feature to archive over 300 MB/sec transfer speed.\\

Like the original [[http://www.hardkernel.com/main/products/prdt_info.php?g_code=G143599699669|CloudShell]], it includes a color LCD and IR receiver on the front,\\ but adds support for UAS and useful data storage technologies (RAID-0, RAID-1 and SPAN).


[[http://www.hardkernel.com/main/products/prdt_info.php?g_code=G149142327280|Where to buy]]

<WRAP left round tip 80%>
CloudShell2 must run Kernel 4.9 based image to utilize the UASP features.\\
Other old Kernel version doesn't support it on XU4.\\
Kernel version must be higher than 4.9.20-24\\
</WRAP>
===== Specifications =====
**Storage**
  * 2 Drive Bays
  * Supported size : 3.5" SATA HDD

**Supported RAID Type**
  * Basic(PM)
  * SPAN
  * RAID 0
  * RAID 1 

**Appearance**
  * Color: Clear, Smoky Blue
  * Size (Height x Width x Depth): 140 mm x 110 mm x 221.5 mm
  * Weight: 0.64kg(without HDD)

**Others**
  * Fan 92 mm x 92 mm (cool and quiet modes)
  * IR Receiver (remote controller not included)
  * 2.8" 320x240 TFT LCD
  * 15V/4A Power Input 

===== Improvements over the original CloudShell (UAS and RAID) =====
One of the key features of CloudShell-2 is USB-Attached SCSI (UAS).  UAS is a new computer protocol used to move data to and from USB storage devices.  UAS depends on the USB protocol, and uses the standard SCSI command set.  UAS provides faster transfers compared to previous USB Storage protocols, which is called Bulk-Only Transport (BOT).  UAS was introduced as part of the USB 3.0 standard, but can also be used with devices complying with the slower USB 2.0 standard, assuming compatible hardware, firmware and drivers [1].

Another important feature of the CloudShell-2 is Redundant Array of Independent Disks (RAID).  RAID is a data storage virtualization technology that combines multiple physical disk drive components into a single logical unit for the purposes of data redundancy, performance improvement, or both.  Data is distributed across the drives in one of several ways, referred to as RAID levels, depending on the required level of redundancy and performance.  The different schemes, or data distribution layouts, are named by the word RAID followed by a number, for example, RAID 0 or RAID 1.  Each schema, or RAID level, provides a different balance among the key goals: reliability, availability, performance, and capacity.  RAID levels greater than RAID 0 provide protection against unrecoverable sector read errors, as well as against failures of whole physical drives [2].  CloudShell-2 supports both RAID 0 and RAID 1.

CloudShell-2 also offers JBOD (Just a Bunch of Disks) as well as RAID.  JBOD generally refers to a collection of hard disks that have not been configured to act as a redundant array of independent disks (RAID) array.  Rather than configuring a storage array to use a RAID level, the disks within the array are either spanned or treated as independent disks.  A spanning configuration uses a technique called concatenation to combine the capacity of all of the disks into a single, large logical disk [3].  CloudShell-2 provides both spanning and independent disk modes as SPAN and PM mode.


====== Hardware ======
**Cloudshell-2 Schematic** : {{ :en:acc:cs2:cloudshell2.pdf |}}

{{:en:cloudshell2_board.jpg?650|}}

===== Hardware Block Diagram =====

{{:en:acc:cs2:cs2_hw_block.png?600|}}


<WRAP hide>
  * [[http://dn.odroid.com/cloudshell/cloudshell_rev0.2.pdf|XU4 Cloud Shell Rev0.2 Schematic]]
  * [[http://dn.odroid.com/cloudshell/cloudshell_rev0.3.pdf|XU4 Cloud Shell Rev0.3 Schematic]]
  * [[http://dn.odroid.com/cloudshell/CloudShell-2015JUN25.dxf|XU4 Cloud Shell 2D drawing (.dxf)]]

</WRAP>

====== Easy installations ======
===== 0. Hardware assembling =====
  * [[en:xu4_cloudshell2:assembling_cs2|Assembling Cloudshell2]]
===== 1. Setting your eMMC or microSD card for Cloudshell2 =====
  * [[en:xu4_cloudshell2:software_settings|Setting your memory card for Cloudshell2]]
===== 2. Set the RAID mode =====
{{:en:raid_select.png?600|}}

There are four data storage modes on the CloudShell2:  **//RAID 0, RAID 1, SPAN//** and **//PM//**.  This means that the hard disks will be detected separately in PM mode.\\
To select the RAID mode, set the RAID Mode DIP Switch to the setting that you want, then apply power while pressing the RAID Setup Key button until booting is complete.

===== 3. Enable LCD and Fan =====
**Don't forget a reboot command after the configurations**

<color #ed1c24>The LCD and Fan tutorial tested on Ubuntu 16.04.</color>

Add PPA your ODROID-XU4
<code>
odroid@odroid:~$ sudo add-apt-repository ppa:kyle1117/ppa
 
 More info: https://launchpad.net/~kyle1117/+archive/ubuntu/ppa
Press [ENTER] to continue or ctrl-c to cancel adding it

gpg: keyring `/tmp/tmp997cpxxq/secring.gpg' created
gpg: keyring `/tmp/tmp997cpxxq/pubring.gpg' created
gpg: requesting key 6AD57103 from hkp server keyserver.ubuntu.com
gpg: /tmp/tmp997cpxxq/trustdb.gpg: trustdb created
gpg: key 6AD57103: public key "Launchpad PPA for KYLE LEE" imported
gpg: Total number processed: 1
gpg:               imported: 1  (RSA: 1)
OK
odroid@odroid:~$
</code>
  odroid@odroid:~$ sudo apt-get update
If successfully the repository is added then you can install the packages by apt-get.
  odroid@odroid:~$ sudo apt-get install odroid-cloudshell cloudshell2-fan
  odroid@odroid:~$ sudo reboot

If you want to install the following server information script, then run the commands.

{{:en:acc:cs2:cs_lcd.png?320|}}
  odroid@odroid:~$ sudo apt-get install cloudshell-lcd
  odroid@odroid:~$ sudo reboot
You can see the lcd script source code following link.

[[http://bazaar.launchpad.net/~kyle1117/+junk/cloudshell-lcd/view/head:/bin/cloudshell-lcd]]
===== 4. Configure the IR Sensor =====
Use the automated tool to configure it. ([[https://github.com/mdrjr/cloudshell_ir|Github Project page]])
<code>wget https://raw.githubusercontent.com/mdrjr/cloudshell_ir/master/install_ir.sh
chmod +x install_ir.sh
sudo ./install_ir.sh
sudo reboot
</code>

===== 5. Revert the TFT LCD settings =====
If you want to display original view on HDMI, then you should run following command.
  sudo systemctl disable cloudshell-lcd.service
====== Detail installations ======
  * [[xu4_cloudshell2_raid_setting|How to set the RAID mode]]
  * [[xu4_cloudshell_lcd_config|Enabling/Configure the LCD]]
  * [[xu4_cloudshell_ir_config|Configuring the IR Sensor on Cloudshell]]
  * [[xu4_cloudshell_smartmontools|Smartmontools upgrade for Cloudshell]]

====== Advanced setup ======
  * [[xu4_cloudshell_lcd_xorg|Xorg on LCD instead of HDMI]]
  * [[xu4_cloudshell_lcd_server|Example program to show server information on LCD]]
  * [[xu4_cloudshell_lcd_backlight|How to turn on/off the LCD back-light]]
  * [[http://forum.odroid.com/viewtopic.php?f=93&t=15666|Dual head implementation]]
  * [[xu4_cloudshell_omv|Enable/Configure the LCD on OMV(Open Media Vault)]

====== References ======
  -   [[https://en.wikipedia.org/wiki/USB_Attached_SCSI]]
  -   [[https://en.wikipedia.org/wiki/RAID]]
  -   [[http://searchstorage.techtarget.com/definition/JBOD]]
   - [[en:xu4_cloudshell2:performance|HELIOS LanTest result]]