We're no longer updating This wiki!!

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
en:c1_hardware [2016/10/13 15:11]
ruppi [Enable the OTG device function on ODROID-C1+]
en:c1_hardware [2017/07/04 11:02] (current)
john1117 [Expansion Connectors]
Line 80: Line 80:
 |37|ADC.AIN1|10bit ADC#1 (0~1.8Volt)| |38|1.8V Power|For ADC reference voltage. Output!| | |37|ADC.AIN1|10bit ADC#1 (0~1.8Volt)| |38|1.8V Power|For ADC reference voltage. Output!| |
 |39|Ground| | |40|ADC.AIN0|10bit ADC#0 (0~1.8Volt)| | |39|Ground| | |40|ADC.AIN0|10bit ADC#0 (0~1.8Volt)| |
 +
 +{{:​en:​c1:​c1_j2_2.png?​600|}}
  
 **J7 - 1x7 pins** **J7 - 1x7 pins**
Line 86: Line 88:
 ^ Pin Number ^ Expansion Net Name ^ Description ^ Driving Capability ^ ^ Pin Number ^ Expansion Net Name ^ Description ^ Driving Capability ^
 |1|Ground| ​ | | |1|Ground| ​ | |
-|2|GPIOAO.BIT6|I2S Data Input  | 2mA |+|2|GPIOAO.BIT6|SPDIF Output ​ | 2mA |
 |3|P5V0| 5.0V Power| | |3|P5V0| 5.0V Power| |
 |4|GPIOAO.BIT8| I2S MCLK | 2mA | |4|GPIOAO.BIT8| I2S MCLK | 2mA |
Line 92: Line 94:
 |6|GPIOAO.BIT9| I2S SCLK | 2mA | |6|GPIOAO.BIT9| I2S SCLK | 2mA |
 |7|GPIOAO.BIT11| I2S Data Output | 2mA | |7|GPIOAO.BIT11| I2S Data Output | 2mA |
 +
 +{{:​en:​c1:​c1_j7_2.png?​600|}}
 ====== UART Console Connector ====== ====== UART Console Connector ======
 <​code>​ <​code>​
Line 106: Line 110:
 ====== Enable the OTG device function on ODROID-C1+ ====== ====== Enable the OTG device function on ODROID-C1+ ======
 C1+ PCB Rev 0.4 2015/09/30 has a new **jumper J8**. C1+ PCB Rev 0.4 2015/09/30 has a new **jumper J8**.
 +
 +<WRAP round important 80%>
 +** Remove the Jumper on J8 if you don't use the USB OTG port as a power input ** \\
 +It will reduce the power consumption and heat significantly.
 +</​WRAP>​
  
 {{:​en:​c1:​c1_20150930.png?​600|}} {{:​en:​c1:​c1_20150930.png?​600|}}
Line 120: Line 129:
 [[http://​forum.odroid.com/​viewtopic.php?​f=113&​t=16864&​p=110766&​hilit=r94#​p110766]] [[http://​forum.odroid.com/​viewtopic.php?​f=113&​t=16864&​p=110766&​hilit=r94#​p110766]]
  
 +//
 +//
 +<WRAP round important 80%>
 ** Caution : Over-Voltage Protection feature ** ** Caution : Over-Voltage Protection feature **
  
-1. The power source must be connected to the DC-Jack. ​ +1. The power source must be connected to the DC-Jack. ​\\ 
- +Micro-USB-OTG and other 5Volt rails have not the protection feature.\\
-Micro-USB-OTG and other 5Volt rails have not the protection feature.+
  
-2. Micro-USB power path Jumper(J8) must be removed to enable the Over-Voltage Protection.+2. Micro-USB power path Jumper(J8) must be removed to enable the Over-Voltage Protection.\\
  
-3. Maximum over-voltage must be lower than 16Volt.+3. Maximum over-voltage must be lower than 16Volt.\\ 
 +</​WRAP>​
 ====== Regulatory Compliance Documents ====== ====== Regulatory Compliance Documents ======
 [[http://​dn.odroid.com/​homebackup/​ODROID-C1_FCC.pdf|FCC]]\\ [[http://​dn.odroid.com/​homebackup/​ODROID-C1_FCC.pdf|FCC]]\\
 [[http://​dn.odroid.com/​homebackup/​ODROID-C1_CE.pdf|CE]]\\ [[http://​dn.odroid.com/​homebackup/​ODROID-C1_CE.pdf|CE]]\\
 [[http://​dn.odroid.com/​homebackup/​ODROID-C1_KCC.pdf|KCC]] [[http://​dn.odroid.com/​homebackup/​ODROID-C1_KCC.pdf|KCC]]
en/c1_hardware.1476340874.txt.gz · Last modified: 2016/10/13 15:11 by ruppi
CC Attribution-Share Alike 3.0 Unported
Driven by DokuWiki Recent changes RSS feed Valid CSS Valid XHTML 1.0